Gate ~ FMCU ~ Benutzerhandbuch/en: Unterschied zwischen den Versionen
< Gate ~ FMCU ~ BenutzerhandbuchZur Versionsübersicht zurückkehren
← Gate ~ FMCU ~ Benutzerhandbuch/en
← Gate ~ FMCU ~ Benutzerhandbuch/en
Writer (Diskussion | Beiträge) (Markierung: 2017-Quelltext-Bearbeitung) |
(→System) (Markierung: 2017-Quelltext-Bearbeitung) |
| (5 dazwischenliegende Versionen von 2 Benutzern werden nicht angezeigt) | |||
| Zeile 150: | Zeile 150: | ||
===Meta information=== | ===Meta information=== | ||
Next step is filling meta information about FMCU | Next step is filling meta information about FMCU | ||
| − | [[Datei: | + | [[Datei:fmcu-configuring-meta-information-en.png]] |
After the input fields have been filled in, you can click on '''Next''' to reach the next page of the wizard. | After the input fields have been filled in, you can click on '''Next''' to reach the next page of the wizard. | ||
| − | === | + | ===Configuration of Gate=== |
| − | [[Datei:fmcu-configuring- | + | [[Datei:fmcu-configuring-configuration-of-gate-en.png]] |
| + | ===WEAC Firmware Update=== | ||
The current WEAC firmware is displayed on the next page of the wizard. If necessary, you can down or upgrade the firmware. | The current WEAC firmware is displayed on the next page of the wizard. If necessary, you can down or upgrade the firmware. | ||
| − | [[Datei: | + | [[Datei:fmcu-configuring-weac-update-en.png]] |
The firmware version for each unit is listed as a label next to the activation button. The navigation options are deactivated during the update process. The update process takes about 3 minutes for both units. | The firmware version for each unit is listed as a label next to the activation button. The navigation options are deactivated during the update process. The update process takes about 3 minutes for both units. | ||
| Zeile 167: | Zeile 168: | ||
After checking the WEAC firmware, the swing doors are configured. It is automatically checked whether the minimum requirements regarding the firmware are met. You will be informed on the surface if the firmware has to be updated first. | After checking the WEAC firmware, the swing doors are configured. It is automatically checked whether the minimum requirements regarding the firmware are met. You will be informed on the surface if the firmware has to be updated first. | ||
| − | [[Datei: | + | |
| + | ===WEAC Doors Update=== | ||
| + | |||
| + | [[Datei:fmcu-configuring-weac-doors-update-en.png]] | ||
If the requirements are met, you can select the swing doors and apply them to the gate. | If the requirements are met, you can select the swing doors and apply them to the gate. | ||
| Zeile 173: | Zeile 177: | ||
[[Datei:image_assistant_step06.png]] | [[Datei:image_assistant_step06.png]] | ||
| + | ===Configuring the Led Player=== | ||
The next step is to configure the LED player for both units (Master and Slave) accomplished. If necessary, you can adjust the parameters. If the status is '''ready for use''', no modifications are necessary. | The next step is to configure the LED player for both units (Master and Slave) accomplished. If necessary, you can adjust the parameters. If the status is '''ready for use''', no modifications are necessary. | ||
| − | [[Datei: | + | [[Datei:fmcu-configuring-led-player-master-en.png]] |
The current firmware of the LED player is shown again on the last page of the assistant. Optionally, you can end the configuration with a restart. However, this is only necessary if IP addresses or interface information have changed. | The current firmware of the LED player is shown again on the last page of the assistant. Optionally, you can end the configuration with a restart. However, this is only necessary if IP addresses or interface information have changed. | ||
| Zeile 631: | Zeile 636: | ||
[[Datei:FMCU-Signale-en.png]] | [[Datei:FMCU-Signale-en.png]] | ||
| + | |||
| + | ===System=== | ||
| + | The information in this section is based on FMCU software v2.6.14. | ||
| + | |||
| + | ====Network==== | ||
| + | |||
| + | [[Datei:FMCU-System-Network-en.png]] | ||
| + | |||
| + | ====Hostname==== | ||
| + | |||
| + | [[Datei:FMCU-System-Hostname-en.png]] | ||
| + | |||
| + | ====Hosts==== | ||
| + | |||
| + | [[Datei:FMCU-System-Hosts.en.png]] | ||
| + | |||
| + | |||
| + | ====CA Certificates==== | ||
| + | |||
| + | [[Datei:FMCU-System-CA-Certificates.en.png]] | ||
| + | |||
| + | ====NTP==== | ||
| + | |||
| + | [[Datei:FMCU-System-NTP.en.png]] | ||
| + | |||
| + | |||
| + | ====nginx==== | ||
| + | |||
| + | [[Datei:FMCU-System-nginx.en.png]] | ||
| + | |||
| + | |||
| + | ====FMCU==== | ||
| + | |||
| + | [[Datei:FMCU-System-FMCU.en.png]] | ||
===Light Schemas=== | ===Light Schemas=== | ||