Gate ~ FMCU ~ Benutzerhandbuch/en

Introduction

The document describes the functions and configuration options of the software Facility Management Control Unit.

The Facility Management Control Unit is software for access control management. It can be used in an enclosed area such as a sports or entertainment center, an airport zone, universities or security areas. The main components of the software solution are:

• An automated passage control with two-part door and signal lighting
• Barcode (or/and RFID) scanners that read identification data from the customer's ticket or card
• Tracking cameras observing the passage of customers
• Info screens showing inbound and outbound information to the customer
• One or more external speakers
• One or more additional monitors with content tailored to customer needs

The main features are:

• Opening access control upon successful ticket validation
• Interaction with customer in response to various events through:
  • Light effects
  • Voice prompts through internal or external speakers
  • Acoustic confirmation of the reading process from barcode scanners
  • Visual content displayed on an info screen
  • Safe opening and closing of the swing doors by monitoring the passage area

Supported operating modes:

• Normal
• Service
• Fire alarm
• Emergency

The variants of Entry Tickets:

• Single entry ticket with closing of access control after passage of one person
• Multiple entry ticket with permanent access control
• Adjustable time intervals
• Consideration of additional conditions about potential-free contacts

Initial Configuration

Step 1

After the software has been downloaded and transferred to the eMMC card according to the documented procedure, see also here Galaxy Gate Inbetriebnahme/en, the login screen appears after the first start. After logging in with the user Installer,

the wizard with the definition of the IP configuration is

configuration wizard will be started.

Network

First step is the network settings configuring

Parameter	Description	Default Value
Address	IP-Address of access control	192.168.1.100
Mask	Network-Mask	255.255.255.0
Gateway	Gateway-Address	192.168.1.1
DNS-Server	DNS-Server for name resolution	192.168.1.1

FMCU Configuration

Next step is selecting FMCU Configuration

Note

The configuration always starts with the "Slave" side of the Galaxy Gate. This selection is preset in the assistant "No Device Slave".

As a type, you can basically make this selection in the assistant.

Configuration of the Facility Management Control Unit

Selection	Description
No Device Slave	Slave Unit (Default Selection)
Galaxy Gate (Modbus Serial)	Master-Unit mit serieller Verbindung zu Slave-Unit
Galaxy Gate (Modbus TCP)	Master-Unit with network connection to Slave-Unit
Galaxy Port (Modbus Serial)	Unit with serial connection to Slave-Unit
Galaxy Port (Modbus TCP)	Unit with network connection to Slave-Unit

Functions

Function	Description
AEA	Configuration for Boarding Gates
Immediate Closure	Closing the swivel arms without swivel range monitoring
Multiple Opening	Swivel arms remain open when multiple input signals are present
Personal Protection	Closing the swivel arms with swivel area monitoring
One-time opening	Single pass even when several input signals are present
Trolley Case	Support of trolley case without alarm
Wheelchair	Assistance from wheelchair without alarm

After the function has been selected, the combination of functions results in corresponding configuration types. The function selection is a filter for the resulting configuration type.

Configuration type from combination of functions

Configuration Type	Description
AEA	Configuration for Boarding Gates
One-time opening Personal Protection	Closing the swivel arms with swivel area monitoring
One-time opening Immediate Closure	Closing the swivel arms without swivel range monitoring
One-time opening Trolley Case	Single passage with trolley case even when several input signals are present
One-time opening Wheelchair	Single passage with a wheelchair even if several input signals are present
Multiple opening personal protection	Closing the swivel arms with swivel area monitoring
Multiple opening instant closure	Closing the swivel arms with swivel area monitoring
Multi-opening trolley case	Swivel arms remain open when several people with wheeled suitcases pass through
Multiple opening wheelchair	Swivel arms remain open when several people with wheeled suitcases pass through

After choosing from the three lists, click on Apply, the application will be restarted, you have to wait for the start-up process to be completed. After logging in again, this screen appears.

Note

If you adjust the IP address in the configuration, you must also align the URL in the browser to the new IP address.

Meta information

Next step is filling meta information about FMCU

After the input fields have been filled in, you can click on Next to reach the next page of the wizard.

Configuration of Gate

WEAC Firmware Update

The current WEAC firmware is displayed on the next page of the wizard. If necessary, you can down or upgrade the firmware.

The firmware version for each unit is listed as a label next to the activation button. The navigation options are deactivated during the update process. The update process takes about 3 minutes for both units.

After checking the WEAC firmware, the swing doors are configured. It is automatically checked whether the minimum requirements regarding the firmware are met. You will be informed on the surface if the firmware has to be updated first.

WEAC Doors Update

If the requirements are met, you can select the swing doors and apply them to the gate.

Configuring the Led Player

The next step is to configure the LED player for both units (Master and Slave) accomplished. If necessary, you can adjust the parameters. If the status is ready for use, no modifications are necessary.

The current firmware of the LED player is shown again on the last page of the assistant. Optionally, you can end the configuration with a restart. However, this is only necessary if IP addresses or interface information have changed.

After clicking Finish

,

you can

now

log in again

with a known credentials

as certain user and work with the Galaxy Gate. If you log in again

with the

as user installer, you get a graphical overview, can find out about the status of the access control and can carry out updates if necessary.

This completes

So you complete the setup of the access control.

You can now log in with a service account and carry out further tests.

Operation Manual

Configuration of the Swing Doors

The swing doors can have different dimensions. Depending on the width and height, this results in other target parameters for optimal curve passage.

After a type has been selected, all parameters can be adjusted according to the needs in the interface before they are then activated via the button Apply in the configuration on the access control. If you change individual values in the display, the settings must first be saved. To do this, click on the diskette symbol on the left of the interface above the file list.

After the changes have been saved, you can activate them using the Apply button.

Configuration of the XOVIS Sensors

Add XOVIS-Sensor

Navigate to "Configuration" -> "Devices" -> "Xovis Cameras" and then click on the "Add" button

The following fields are filled in the order shown:

1. Name
2. URL
3. Username
4. Password

The configuration is saved by clicking the Save button.

Note

After adding the XOVIS sensor, the FMCU must be restarted before proceeding with the configuration.

Add XOVIS monitoring area as alarm signal

Navigate to "Configuration" -> "Signals" and then click on the "Add" button

The following fields must be filled in here:

1. Select type "XOVIS Sensor"
2. Specify the name of the signal (e.g. "XOVIS ALARM")
3. Set the minimum number of people in the alarm zone to trigger an alarm (e.g. 2)
4. Select the alert type (e.g. "Unauthorized Access")
5. Determine a list of alarm zones (e.g. "AlarmZone")
6. Select the XOVIS sensor added to.

The configuration is saved by clicking the Save button.

Add XOVIS counter

Navigate to "Configuration" -> "Signals" and then click on the "Add" button

The following fields must be filled in here:

1. Select type "XOVIS Sensor".
2. Specify the name of the signal (e.g. "XOVIS Counter")
3. Specify the side of the gate (e.g. "Entrance")
4. Set the value "Counter".
5. Specify a list of lines(e.g. "EntryLine")
6. Select the XOVIS camera that you added earlier.

The configuration is saved by clicking the Save button.

Store VPN key

A VPN key is required to use remote maintenance. This key can be requested from maxcrc support (support@maxcrc.de) by specifying the project name (Configuration->General view).

After the key file (*.opvn.conf) is available, you can import via the System->OpenVPN page. The following steps are necessary for this.

Navigating to the System-OpenVPN page.

This file is now specified via the Select file button in the file selection dialog. Then click on Upload. When the process has been successfully completed, an info icon will appear next to the start button. This means the file has been uploaded successfully, the OpenVPN client can now be activated by clicking on Start.

If the start was successful, the color changes from green to red and the label from start to stop. The status of the OpenVPN client and the IP address for access in the VPN network for this gate are displayed to the right of the info symbol. You can disable remote access by clicking the Stop button.

SoftwareupdatesUpdate Software

If there is no Internet connection, individual package installations can be carried out

in

using the System->Update software menu.

To do this, you create

You should have a zip archive with the packages to be installed

beforehand

. It must be ensured that no relative paths are used in the archive. Then you can insert the archive into the input line via Select file and start the update procedure with Upload. The progress of update process is displayed

in the interface. Display during installation Anzeige nach Abschluss der Installation

:

If necessary, the application can be restarted.

Customer Role

When you log in

with the

as user client, a simplified interface appears with

only three configuration menus

"Home", "Status", "Statistics" configuration menus.

In this view you can administrate the access control, but you cannot make any configuration adjustments. The current statistics are displayed directly on the interface, a complete overview of the accesses can be viewed in the Statistics tab and exported if required. The current status of the individual access control components can be viewed in the Status tab. The

Cleaning

Clearance option disables all alarms to make the cleaning staff's job easier. The Emergency

open

option supports the user in opening the access control immediately.

Standard assignment connection boardAssignment Connection Board

Unit 1

Port	Function	Description
LSU (E1)	LS Middle Center Light barrier	NO Normally Open Contact
LSV (E2)	LS Entry Photocell Input	NO normally open contact
E3	Open Entry Single free entry direction Impuls 0,1-1,0 Sek.	NO Normally Open Contact
E4	Open Exit Single free exit direction Impuls 0,1-1,0 Sek.	NO normally open contact
LSH (E5)	NA not connected
E6	State bit 0 Status bit 0	NO normally open contact
E7	State bit 1 Status bit 1	NO normally open contact
E8	Fire Alarm fire alarm system (BMA)	NC normally closed contact
E9	Open Entry 70% Einzelfrei 70% Input Direction Impuls 0,1-1,0 Sek.	NO normally open contact
E10	Emergency Open Button emergency button	NC normally closed contact
A8	Entry Confirmation Confirmation of passage entry direction Impuls 0,5 Sek.	+12 VDC
A9	Exit Confirmation Confirmation of passage exit direction Impuls 0,5 Sek.	+12 VDC

Unit 2

Port	Function	Description
LSU (E1)	NA not connected
LSV (E2)	NA not connected
E3	Open Entry Single free entry direction Impuls 0,1-1,0 Sek.	NO normally open contact
E4	Open Exit Single free exit direction Impuls 0,1-1,0 Sek.	NO normally open contact
LSH (E5)	LS Exit Photocell exit	NO normally open contact
E6	State bit 2 Status bit 2	NO normally open contact
E7	State bit 3 status bit 3	NO normally open contact
E8	Fire Alarm fire alarm system (BMA)	NC normally closed contact
E9	Open Exit 70% single free 70% exit direction Impuls 0,1-1,0 Sek.	NO normally open contact
E10	Emergency Open Button emergency button	NC normally closed contact
A8	Alarm Impuls Alarm Impuls 0,5 Sek.	+12 VDC
A9	Gate State Error error condition Durchgang	+12 VDC

Status ZustandsbitsBits

Status	Unit 1 E6 Bit 0	Unit 1 E7 Bit 1	Unit 2 E6 Bit 2	Unit 2 E7 Bit 3
Normal Normal	0	0	0	0
Free Entry Entrance permanently free	1	0	0	0
Lock Entry entrance blocked	0	1	0	0
Service Entry Permanently open entry direction	1	1	0	0
Free Exit Exit permanently free	0	0	1	0
Free Entry/Exit Input/Output permanently free(Not implemented)	1	0	1	0
Lock Entry / Free Exit Entrance blocked / exit permanently free	0	1	1	0
tbd	1	1	1	0
Lock Exit exit blocked	0	0	0	1
Free Entry / Lock Exit Entrance permanently free / exit blocked	1	0	0	1
Lock Gesperrt	0	1	0	1
tbd	1	1	0	1
Service Exit Permanently open exit direction	0	0	1	1
tbd	1	0	1	1
tbd	0	1	1	1
Self Test self test	1	1	1	1

AlarmdefinitionAlarms Definition

An alarm is triggered as a follow-up action from signals or other sources (e.g. devices). Navigate to "Configuration" -> "Alarms".

To create the alarm click on the "Add" button:

An alarm exists has several general characteristics. This includes a name, the definition of an action... : Name, Enabled Status, Priority, Sounds settings, Light settings, etc.

In the table below there are descriptions of existing alarms.

Definition	Description	Status
Connection Alive	monitors connection to external application	on/off
Connection Lost	monitors connection to external application	on/off
Counter Pass	is set by anti-rotation protection is activated	on/off
Door Break-In	Door is forcibly moved when closed	on/off
Emergency	is set if the signals on unit 1 E8 or unit 2 E8 are not active (opener).	on/off
Fire Alarm	is set if the signals on unit 1 E10 or unit 2 E10 are not active (opener).	on/off
Invalid Ticket	is set if ticket validation fails	Impuls
Motionless Object	is set when an object is in the gate area for more than a defined period of time and closing is prevented by a timeout.	on/off
No Alarm	is set if no alarm is defined for signals	on/off
Proceed Alarm	analogous to Motionless Object with a different time span and other actions without light indication	on/off
Server Alarm	is triggered in the FMCU server	on/off
Tailgating	is set if more than one person is in the gate area	on/off
Unauthorized Access	is set if a person is in the gate area when the gate is closed	on/off
Valid Ticket	is set if the ticket validation was successful (trigger beep)	Impuls

SignaleSignals

Die Informationen in diesem Abschnitt basieren auf der FMCU-Software The information in this section is based on FMCU software v2.3.7 und der and WEAC -Version version 32.14.

Technischer Hintergrund

System

Die Software FMCU basiert auf einem angepassten UNIX-Betriebssystem, welche unter Anwendung des Yocto-Projektes produziert worden ist. Es werden nur die benötigten Dienste im Betriebssystem aktiviert. Es werden die für den CPU-Typ optimalen Unterstützungspakete bei der Erstellung des Betriebssystems berücksichtigt. Diese sogenannten The information in this section is based on FMCU software v2.6.14.

Network

Hostname

Hosts

CA Certificates

NTP

nginx

FMCU

Light Schemas

To navigate the section click "Configuration" -> "Light Schemas". Here you can add and/or customize named color schemes.

Each schema describes the colors and behaviour of FMCU lights elements like enter and exit zones and the door. Existing light schema you can use in settings of Gates and Alarms.

Click Add to create light schema or click "pen" in the table to edit existing schema.

Each light schema is described by the fields below

Field	Description
Name	Name of light schema
Priority	Priority of using light schema if there is competition situation. Less value means more priority
Color Entry On	Color of the gate entry zone during "On" time period
Color Exit On	Color of the gate exit zone during "On" time period
Color Door On	Color of the doors during "On" time period
Light Schema On, ms *	Length of "On" time period in ms
Light Schema Off, ms *	Length of "Off" time period in ms
Color Entry Off	Color of the gate entry zone during "Off" time period
Color Exit Off	Color of the gate exit zone during "Off" time period
Color Door Off	Color of the doors during "Off" time period
Led Image Entry *	Selected image of the gate entry zone (Arrow, Cross, Empty)
Led Image Exit *	Selected image of the gate exit zone (Arrow, Cross, Empty)
Running Light	Using "runing light" for the light schema (option)

Click on any field for color to edit color of selected gate element

You can select the color space (RGB, HSL, HEX) to set the required color

Lights

To navigate the section click "Configuration" -> "Lights". Here you can add and/or customize light configurations for different gate's modes.

Each configuration has its own name. The image above shows the default light configuration. Click Add to create configuration, or "pen" to edit existing one.

For each mode select existing light schema.

Then you can use the light configuration in "Devices" -> "Gates" settings.

Press "pen" to edit gate settings, and select light configuration.

Technical Background

The FMCU software is based on a customized UNIX operating system, which has been produced using the Yocto Project. Only the required services are activated in the operating system. The optimal support packages for the CPU type are taken into account when creating the operating system. These so-called Board Support Packages (BSP) werden von den Hardwareherstellern zur Verfügung gestellt und gestatten eine optimale und effiziente Ausnutzung der Hardwareressourcen.

Funktionen

are provided by the hardware manufacturers and allow optimal and efficient utilization of the hardware resources.

Functions

Grundsätzlich werden die Funktionen über die Signalverabeitung abgebildet. Die Signale werden durchunterschiedliche Quellen erzeugt. Dazu gehören:

• Lichtleiste
• Lichtsensor
• Deckensensor
• Sonstige

Die Anordnung der Sensoren ist in der nachfolgenden Abbildung dargestellt. In jeder Rahmenhälfte befindet sich eine sogenannte "Inner-Zone" und eine "Outer-Zone". Bei Durchschreiten einer Zutrittskontrolle wird ein Signalflussdiagramm erzeugt, welches für die Abbildung der nachfolgenden Funktionen genutzt wird. Die Lichtleiste dienst als Quelle für mehrere Signale und ist ebenfalls in unterschiedliche Bereiche unterteilt. In der Standardkonfiguration sind folgende Signale konfiguriert. Signalname Rahmenhälfte Entry Confirmation Eingang

In principle, the functions are mapped via the signal processing. The signals are generated by different sources including:

• Light bar
• Light sensor
• Ceiling sensor
• Other

The location of the sensors is shown in the figure below. In each half of the frame there is a so-called "inner zone" and an "outer zone". When passing through an access control, a signal flow diagram is generated, which is used to map the following functions.

The light bar serves as a source for several signals and is also divided into different areas.

The following signals are installed in the standard configuration.

Signal Name	Frame Half
Entry Confirmation	Entry
Entry Gate Sensor [U1_E2]	Eingang Entry
Entry Outer LightBar	Eingang Entry
Exit Inner LightBar	Eingang Entry
Free Entry [1000]	Eingang Entry
Lock Entry [0100]	Eingang Entry
Open Entry [U1_U2_E3]	Eingang Entry
Open Entry 70% [U1_E9]	Eingang Entry
Remote Open Entry	Eingang Entry
Service Entry [1100]	Eingang Entry
Emergency Remote	Ausgang Exit
Emergency [U1_U2_E8]	Ausgang Exit
Entry Inner LightBar	Ausgang Exit
Exit Confirmation	Ausgang Exit
Exit Gate Sensor [U2_E5]	Ausgang Exit
Exit Outer LightBar	Ausgang Exit
Free Exit [0010]	Ausgang Exit
Lock Exit [0001]	Ausgang Exit
Open Exit [U1_U2_E4]	Ausgang Exit
Open Exit 70% [U2_E9]	Ausgang Exit
Remote Open Exit	Ausgang Exit
Service Exit [0011]	Ausgang

Schliessfahrt mit reduzierter Geschwindigkeit

Exit

Closing-run at reduced Speed

Diese Funktion ist für Signale zutreffend, die die Eigenschaft This function applies to signals that have the property CloseGate > 0 aufweisen. Bei den betroffenen Signalen muss der Wert . For the affected signals, the value Close gate speed, % * mit einem Wert zwischen 10 und 100% definiert werden. Es besteht somit die Möglichkeit, für unterschiedliche Durchgangszenarien entsprechende Schließgeschwindigkeiten zu definieren. Der Standardwert ist auf 100% festgelegt. In der Standardkonfiguration erfüllen folgende Signale diese Voraussetzung must be defined with a value between 10 and 100%. It is therefore possible to define appropriate closing speeds for different passage scenarios. The default value is set to 100%. In the standard configuration, the following signals meet this requirement.

Signal	Parameter Wert	Value
Tailgating watcher	Close gate speed, % *	100%
Entry Gate Sensor [U1_E2]	Close gate speed, % *	100%
Exit Gate Sensor [U2_E5]	Close gate speed, % *	100%
Entry Outer LightBar	Close gate speed, % *	100%
Exit Outer LightBar Exit	Close gate speed, % *	100%

DurchgangsbestätigungPassage Confirmation

Diese Funktion setzt einen Impuls mit einer einstellbaren Zeitdauer im Anschlussboard für den Anschluss A8.Zusätzlich wird erfolgte Durchgang in der Statistik berücksichtigt.

Koffertrolleyerkennung

This function sets an impulse with an adjustable duration in the connection board for connection A8.

Suitcase Trolley Detection

Diese Funktion ist aktiv wenn bei folgenden Signalen die aufgeführten Parameter gesetzt werden. Es bedeutet, dass eine Personen mit einem hinter sich herziehenden Koffer ohne Störung durch vorzeitig schleißende Schwenktüren passieren kannThis function is active when the listed parameters are set for the following signals. It means that a person with a suitcase being pulled behind them can pass through prematurely closing swing doors without being disturbed.

Signal	Parameter Wert	Value
Middle Gate Sensor [U1_E1]	Protect from force close	true
Inner LightBar	Protect from force close	true

MehrfachöffnungMultiple Opening

Diese Funktion ist nur dann gültig, wenn ein Leser für die Eingangsrichtung eingerichtet worden ist. Es bedeutet, dass mehrere Personen in einer Reihe nacheinander den Eingang passieren können, ohne dass die Schwenktür zwischenzeitlich geschlossen wird. Es muss von jeder Person ein Ticket am Kartenleser am Eingang präsentiert werden. Nur bei erfolgreicher Validierung bleiben die Schwenktüren geöffnet. Diese Funktion ist aktiv wenn bei folgenden Signalen die aufgeführten Parameter gesetzt werdenThis function is only valid if a reader has been set up for the entry direction. It means that several people can pass through the entrance in a row without the swing door being closed in the meantime. Each person must present a ticket at the card reader at the entrance. The swing doors only remain open if the validation is successful. This function is active when the listed parameters are set for the following signals.

Signal	Parameter Wert	Value
Middle Gate Sensor [U1_E1]	Protect from force close	true
Inner LightBar	Protect from force close	true
Entry Outer LightBar	Protect from force close	true
Entry Gate Sensor [U1_E2]	Protect from force close	true
Tailgating watcher	Aktiviert Activated	false

Tipps zum ArbeitenTips for Working

Wenn man die Übersicht bei der Konfiguration der Signale verloren hat, kann man über die Funktion If you have lost the overview when configuring the signals, you can use the function

Reset to Default

einen definierten Ausgangszustand wiederherstellen restore a defined initial state.

Hinweis Wenn man die Funktion Note

If you use the "Rest to Default" anwendet, gehen die aktuellen Einstellungen verloren. Man kann bei Bedarf vor diesem Schritt die aktuelle Konfiguration exportierenfunction, the current settings will be lost. If necessary, you can export the current configuration before this step.

Verwandte Themen

• Galaxy Gate Bedienungsanleitung
• Beschreibung zentrales Dashboard
• Galaxy Gate Inbetriebnahme
• Applikationsserver Zutrittskontrollen
• Zutrittskontrollen Checkliste IT Infrastruktur